BOOM
Inverted T-cross section, 4 or 5-section telescoping type, extended and retracted proportionally by a double-acting hydraulic cylinder and cable-crowd system. Equipped with easily replaceable teflon-plugged nylatron wear pads for smooth operation.

102SX - 4-Section 29' 9" (9,1 m) to 102' (31,1 m). 2-Section, 26' (7,9 m) to 46' (14,0 m) jib.

124SX - 5-section 30' 10" (9,4 m) to 123' 6" (37,6 m). 1-Section, 31' (9,5 m) jib or 2-Section, 30' 6" (9,3 m) to 55' (16,8 m) jib.

Quick Reeve Boom Point – Five high-density nylon load sheaves mounted on heavy-duty roller bearings. Two removable pin-type rope guards.

Boom Elevation – Double-acting hydraulic cylinder. Working range from 6° below horizontal
to 80° above.

Load Hook – 5-ton (4,5 mton) capacity hook with heavy-duty swivel and weight is provided for single-line operation. 

HOIST
102SX - Maximum theoretical line speed 300 fpm (91 mpm). Maximum theoretical bottom-layer line pull 11,500 lb (5 216 kg). Two-speed planetary reducer with wet multi-disc spring applied, pressure-released internal brake and grooved drum.

Wire Rope - 335' (102,1 m) of 9/16" (14,3 mm) diameter rotation resistant type.

124SX - Maximum theoretical line speed 453 fpm (138 mpm). Maximum theoretical bottom-layer line pull 13050 lb (5 919 kg). Two-speed planetary reducer with wet multi-disc spring applied, pressure-released internal brake and grooved drum.

Wire Rope – 380' (115,8 m) of 5/8" (16 mm) diameter rotation resistant type.

SWING SYSTEM
Free swing continuous rotation system. Externally mounted, double-reduction planetary gearbox driven by hydraulic motor. Equipped with a dual brake system; spring-applied hydraulically-released Parking Brake and a foot actuated Dynamic Service brake. Ball-bearing swing circle with external gear. Manitex ACCUSwing control allows operator to adjust crane swing speed up to a maximum of 2.0 rpm (nominal).

OUTRIGGERS
Patented X-style outrigger provides all around stability to create a true 360° work zone without need of a front mounted stabilizer. Design incorporates double-acting hydraulic cylinders; operated independently for precise leveling. Bubble level located near outrigger controls.

MOUNTING
Lower frame is mounted to chassis by threaded rods and clamp plates. No welding to truck chassis is required.

Rear Underride Protection – Supplied on factory mounted cranes. Fabricated structure mounted at rear of carrier. Complies with Bureau of Motor Carrier Safety Standard 393.86.

Lower Frame – Torsion resistant, rigid welded plate design with integrated pedestal.

Boom Rest – Heavy-duty fabrication. Easily removed to simplify loading and unloading truck deck.

CONTROL SYSTEM
Single operator platform and seat mounted to turret. Four "pilot operated" single-axis crane controls provide precise metering and multifunction capability. Swing is further refined using Manitex ACCUSwing control to allow setting to individual operator preference. Optional free swing is available to assist in tandem lifting and centering of boom over loads. Controls are arranged in accordance with ANSI B30.5 standards. The operator station also includes engine start/stop, air foot throttle, signal horn, load moment indicator display, boom angle indicator, load chart and range diagram. Enclosed cab and heater are optional.

HYDRAULICS
Hydraulic System – A 3-section pump direct-mounted to power take-off on truck transmission provides 41.7 gpm (158 lpm) to the hoist, 28 gpm (106 lpm) to the boom hoist, telescope and outrigger circuit, and 12 gpm (45 lpm) to the swing circuit. 100-gallon (379 liter) hydraulic reservoir with strainer and a 10-micron filter in the return line. Ball-type shutoff valve and strainer are provided in suction line. Use of SAE O-ring and face seal O-ring hydraulic fittings throughout system.

Hydraulic Cylinders – All load-holding cylinders are equipped with integral holding valves.

WARNING SYSTEMS
Load Moment Indicator (LMI) – CAN bus system maximize expansion capabilities. Senses boom hoist cylinder pressure, boom length and boom angle. Audio-visual warning indicates overload conditions and overload shutoff feature prevents continuing overload. Operator can access all load conditions via display at the operator station. Internal boom length cable.

Radio Anti-Two-Block System – Audible warning and shutoff functions prevent hook from contacting boom point.

Back-Up Alarm – Electronic audible motion alarm activated when truck transmission is in reverse gear.

GENERAL
Electrical – State-of-the-art, weather-resistant components throughout. Hermetically sealed power in relays. Enclosure includes power in relays and circuit status LEDs. Designed to withstand high pressure washing and varying climates.

Design/Welding – Design conforms to ANSI B30.5. Welding conforms to AWS D1.1. Tested to SAE 1063 and SAE 765.

Manuals – Operator, service and parts manuals depict correct crane operation, maintenance procedures and parts listing.

Warranty – 12-month warranty covers parts and labor resulting from defects in material and workmanship.

Note: In order to ensure continuous improvement, specifications may change without notice.